New to this site

General JointCAM questions and discussion
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
cusoak
Posts: 4
Joined: Tue Aug 28, 2018 8:02 am
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

New to this site

Postby cusoak » Wed Sep 12, 2018 8:08 am

Hi New here. Looking at this forum I see that there is not a whole lot of activity here.
I was just wondering how many copies of the software have been sold?
Jeff

G-Force_Admin
Site Admin
Posts: 74
Joined: Tue Sep 23, 2014 5:10 pm
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: New to this site

Postby G-Force_Admin » Wed Sep 12, 2018 8:27 pm

There are a few hundred JointCAM users, but only a small percentage have registered for the forum.
Most of the posts here occurred when JointCAM was first released.
I think that people tend to email me directly when they have questions.

I'll probably be closing this forum sometime next year and starting a FaceBook page in it's place.
Gerry

cusoak
Posts: 4
Joined: Tue Aug 28, 2018 8:02 am
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: New to this site

Postby cusoak » Sat Sep 15, 2018 9:28 am

Ok I want to buy your program to do box joints,
I want to make boxes out of 1/2"material
The sides will be 4" wide and 9"tall bottom will be the same size.
I need to create joints on the bottom only
The top will have a rabbit on both ends and just sit on the sides.
Would/ could you show me with screen shots of how to set up that to cut in the pins and tails.
You can just email me with the reply
Thanks Jeff

G-Force_Admin
Site Admin
Posts: 74
Joined: Tue Sep 23, 2014 5:10 pm
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: New to this site

Postby G-Force_Admin » Sat Sep 15, 2018 12:57 pm

Attachments
box-1.jpg
box-1.jpg (149.19 KiB) Viewed 10572 times
Gerry

cusoak
Posts: 4
Joined: Tue Aug 28, 2018 8:02 am
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: New to this site

Postby cusoak » Thu Jun 13, 2019 3:05 pm

Before I but I have a question.
I have a shapeoko xxl made by Carbide 3D
I run Carbide motion to run the Gcode.
If your program compatible with Carbide motion.
And has the price of the soft ware changed.
Thanks Jeff

G-Force_Admin
Site Admin
Posts: 74
Joined: Tue Sep 23, 2014 5:10 pm
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: New to this site

Postby G-Force_Admin » Sun Jun 30, 2019 10:32 am

Sorry, I missed this post.

According to this list of supported g-codes, JointCAm produced code should run fine.
https://docs.carbide3d.com/software-faq ... ed-gcodes/

JointCAM uses very basic g-codes, G0, G1, G2, and G3.
It does use helical G2/G3 moves when plunging into mortises, but I would expect them to work fine as well.

Yes, the price went up a few months ago when mortise and tenon joints were completed.
JointCAM was first released at a reduced price, with the price increasing each time new joints were added.

For quicker replies, email support at g-forcecnc.com.
Gerry

G-Force_Admin
Site Admin
Posts: 74
Joined: Tue Sep 23, 2014 5:10 pm
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable

Re: New to this site

Postby G-Force_Admin » Sun Jun 30, 2019 10:35 am

According to this, helical arcs are supported, as I suspected.

https://docs.carbide3d.com/software-faq ... finitions/
Gerry


[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
[phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable